Yahoo! JAPAN

検索設定 - この検索結果ページについて

SATA command IDENTIFY DEVICE transfer で検索した結果 1~10件目 / 約1,120,000件 - 0.47秒

ウェブ

  1. ATA Command Set - 4 (ACS-4) - T13
    B) multiple descriptions that involved the DEVICE RESET command ... Incorporated f14120r1 – IDENTIFY DEVICE data word 53 PATA/SATA/… cleanup ; ... SMART Command Transport (SCT) was removed from the normative.
    t13.org/.../di529r18-ATAATAPI_Command_Set_-_4.pdf
  2. ATA/ATAPI Command Set - T13
    This standard specifies the AT Attachment command set between host systems and storage devices. .... 12) Integrated e04127r0 – This makes SATA signatures reserved with no .... 9) Incorporated e05132r1 – Report transport standard. IDENTIFY. DEVICE words 222 and 223 were assigned for this purpose.
    www.t13.org/documents/.../docs2006/d1699r3f-ata8-acs.pdf
  3. SAT: ATA PASS THROUGH sector count for IDENTIFY DEVICE - T10.org
    But Jim is quite correct on the DMA and PIO protocols, all of them require data transfer. ... One tool wants to send an ATA IDENTIFY DEVICE command through the SAT pass-through to a SATA disk inside an external USB ...
    www.t10.org/pipermail/t10/2010-April/015087.html
  4. Device Command Layer Protocol
    SATA Device Command Layer Protocols. Power-on and COMRESET. DHR0: Hardware_reset_asserted. Command Layer has received a message from the Transport Layer that a COMRESET has been asserted; Device stays in this state until ...
    www.iol.unh.edu/.../sata/SATA_Protocol_Chapter_11_a...
  5. ATA Interface Reference Manual - Seagate
    5.2.3 DMA data transfer commands . .... device with an embedded controller that interprets and executes the ...... The Identify. Drive and Read Buffer commands each transfer a single block of 512 bytes. The Read Long ...
    ftp.seagate.com/acrobat/reference/111-1c.pdf
  6. DB35 Series SATA - Seagate
    See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48- ... Sustained transfer rate OD (Mbytes/sec max). 65.0. I/O data-transfer rate (Mbytes/sec max). 150 (SATA 1.0). Interleave. 1:1.
    www.seagate.com/staticfiles/support/.../100362348d.pdf
  7. _IDENTIFY_DEVICE_DATA (ata.h) - Windows drivers | Microsoft Docs
    The IDENTIFY_DEVICE_DATA structure contains the data retrieved by an ATA identify device data command (0xEC).Note The ATA port driver and ATA miniport driver models may be altered or unavailable in the future.
    docs.microsoft.com/en.../ns-ata-_identify_device_data
  8. Flat Panel Transfer Board (FPTB) User's Manual - Advantech
    delivers a SSD for native Serial Advanced Technology Attachment (SATA) hard disk drive drop-in replacement ..... The following table details the sector data returned after issuing an IDENTIFY DEVICE command. Table 14 ...
    advdownload.advantech.com/.../96FD42-N032-LIS_ ...
  9. Serial ATA II Native Command Queuing Overview - Intel
    Performing Multiple Read Commands using SATA II Native Command Queuing .. ...........17. 5.3.1 .... Direct Memory Access (DMA) is a means of data transfer between the device and host memory without host .... the Service command to determine which command the data transfer is for, and then the host will.
    www.intel.com/assets/pdf/whitepaper/252664.pdf
  10. SATA AHCI-IP reference design manual
    within each command slot, and transfers Command FIS to SATA-IP. Based on ... SATA device to select the active command by DMA Setup FIS. .... The host sends IDENTIFY DEVICE command to check disk information.
    dgway.com/.../SATA-IP/dg_sataahciip_refdesign_en.pd...
  1  2  3  4  5  6  7  8  9  10  次へ »
検索設定 - この検索結果ページについて

Copyright (C) 2019 Yahoo Japan Corporation. All Rights Reserved.