PRECUT THE FLEECE FOR WRAPPING THE PIPE

ENSURE THE FLEECE WILL EXTEND 4 UP THE PIPE AND 2 ONTO THE FIELD

DRY FIT ALL OF THE FLEECE PIECES

LEAVE A SMALL "TAG" AT THE END OF THE TAPE ON THE PIPE TO MAKE REMOVAL EASIER

ALWAYS WEAR PROPER PPE WHEN USING ALSAN FLASHING

APPLY ALSAN FLASHING TO PIPE AT A RATE OF TWO GALLONS PER SQUARE

APPLY THE ALSAN FLASHING INTO THE 1 OVERLAP IN THE FLEECE

APPLY TO THE OTHER HALF OF THE FIELD AREA AT A RATE OF 2 GALLONS PER SQUARE

REMOVE THE TARE AROUND THE PIPE

WAIT FOR THE COAT TO DRY AND THEN BRUSH OFF REMAINING GRANULES

Prime area and install Aashing

Apply CATALYZED base layer application

Roll out fleece reinforcement

Roll out wrinkles and bubbles

Apply top application

Completely saturate fleece

Install subsequent fleece

Establish a two-inch side overlap of the reinforcement

Surface Preparation

Surface Prep

Primer Layer

Alsan RS Paste

Mortar System

Color Finish

Batch mixing

Installing the fleece

Apply Masking Tape

Surface preparation

Mixing the resin

Catalyst ratio

Resin temperature

Applying the resin

Applying the base coat

Remove the masking tape

ALSAN RS INSTRUCTIONAL VIDEO Wall Flashing Application

Apply primer and remove masking tape

Reapply masking tape once dry

Apply corner gusset fleece

Apply base layer application

Install Reece and apply top application

Fully saturate fleece

Remove masking tape prior to curing

ALSAN RS INSTRUCTIONAL VIDEO Rail Poul Flashing Application

Prepare surface and prime, as necessary

Install fully reinforced liquid flashing on vertical

Fully saturate reinforcing fleece

Install target reinforcement

Install fully reinforced field membrane

Fully encapsulate the nuts with Alsan RS Detailer

SOPREMA PRODUCT INFORMATION VIDEO ALSAN RS 230 FLASH and ALSAN RS 260 LO FLASH

260 LO Flash is the available low-odor version.

Resin is always installed in conjunction with RS Fleece

The result is a fully reinforced liquid membrane ...

230 & 260 LO Flash are available in 12 kg quantities

Resin must be mixed prior to adding catalyst.

Resin is spread with a roller.

Reinforcement is then installed and rolled smooth.

Additional resin is then applied to saturate fleece.

RS Flash is "moldable" to nearly any shape and projection.

Alsan Flashing is a single component urethane bitumen hybrid

No special tools are required for an Alsan Flashing application

Apply base layer onto a clean substrate

No primer is required with Alsan Flashing

Reinforcement is installed at transition changes

After two to five hours, a final layer is applied

Alsan Flashing is resistant to UV so it can be left exposed

Or, granules may be applied into the still wet layer

Sweep off excess granules after two hours

In lieu of granules, Alsan Finish can also be applied

The two rules of Aashing a projection

Install target fleece four inches from base of vertical

Mask off application area

Apply CATALYZED primer

Remove tape prior to curing

Pre-cut and dry fit fleece reinforcement

Apply CATALYZED base layer application

Install fleece reinforcement

Remove wrinkles and fully saturate fleece

Remove masking tape prior to curing

Alsan RS 233 Mortar is composed of RS 210 Resin

Pour Alsan RS 210 into large container

Mix contents thoroughly

Add CATALYST activator

Each 33 kg quantity will cover 102 ft (9.5 m)

Numerous surfacing options may now be applied

Mask off application area

Apply CATALYZED primer

Apply CATALYZED base layer application

Install corner gusset fleece

Fully saturate fleece

Install subsequent fleece reinforcement and saturate

Remove masking tape prior to curing

Quartz is set into a CATALYZED bed of RS 233 Mortar

Broadcast quartz into uncured 233 Mortar

Allow to dry and remove excess aggregate

Apply CATALYZED Alsan RS 281 Clear Finish

A variety of colors and blends are available

ALSAN RS TEXTURED FINISH Balcony Application Brooklyn, New York

Thoroughly pre-mix RS Finish Base & Color Pack.

Add catalyst activator

Apply with roller

Mask off application area

Apply CATALYZED primer

Remove tape prior to primer curing

Once dry, re-apply masking tape

Pre-cut fleece reinforcement

Apply CATALYZED base layer application

Install fleece

Fully saturate fleece

Install target fleece

Remove tape prior to curing

SOPREMA INSTRUCTIONAL VIDEO Condut Pipe Flashing with ALSAN RS

Two rules for flashing projections

Extend vertical fleece two inches onto horizontal

Install target fleece four inches from base of vertical

Mask off area and apply primer

Remove tape prior to curing

Reinstall masking tape and apply base application

Install pipe fleece reinforcement

Install target base fleece

Fully saturate reinforcement