AMD AM5 INSTALLATION GUIDE

AMD mounting bracket pre-installed

Apply the thermal grease to the CPU surface

Place the cooler on the CPU

Clasp the hooks of the AMD mounting bracket onto the plastic notch at the top end of the AMD CPU socket, as illustrated

Attaching the fan to the cooler

Connect the fan's 4-pin header to the CPU fan power socket on the motherboard

INTEL LGA1700 INSTALLATION GUIDE

Insert the clips into the proper holes on the Intel mounting bracket

Apply the thermal grease to the CPU surface

Press the push-pins into the clips and ensure the Intel mounting bracket is safely installed on the motherboard

AMD mounting bracket pre-installed

Place the cooler on the CPU

Clasp the hooks of the AMD mounting bracket onto the notch on the underside of the Intel mounting bracket as illustrated

Attaching the fan to the cooler

Another LGA1700 bracket installation method

Insert the clips into the proper holes on the Intel mounting bracket

Clasp the hooks of the AMD mounting bracket onto the notch on the underside of the Intel mounting bracket, as illustrated

Apply the thermal grease to the CPU surface

Place the cooler on the CPU

Press the push-pins into the clips and ensure the Intel mounting bracket is safely installed on the motherboard

Attaching the fan to the cooler

Connect the fan's 4-pin header to the CPU fan power socket on the motherboard

Connect power cable to COOLERGENIE's power cable port

Connect power cable to COOLERGENIE port of the power supply

Connect PWM signal cable to COOLERGENIE's M/B PWM port

Connect PWM signal cable to CPU fan connector of MB

Connect the CPU cooler fan to COOLERGENIE's cooler fan port

Connect the case fan(s) to COOLERGENIE's case fan port(s)

Enter the BIOS to set the CPU fan control to the PWM mode

Use the magnetic strips or Velcro to fasten the COOLERGENIE

Select your preferred Semi-fanless mode

Attach the fan to the radiator

Insert the position screws into the corresponding place on the back plate, then use the washers to fix the position screws.

Install the back plate on the back of the motherboard

Fasten the Intel LGA 2011 screws to the motherboard

Remove the protective film from the cold-plate, and place the pump on the CPU

Connect the pump power connector to the motherboard

RGB Lighting Synchronization via Motherboard (RGB header 3 pin assignment is 5V/D/G)

Connect fan's RGB connectors together

RGB Lighting Synchronization via Integrated RGB Control Box *Only LIQMAX III ARGB 360 model includes the RGB control box

Connect the fan RGB connector to the control box

Attach the fans to the radiator

Place the washers into the position screws and fix them with stand-offs

Apply the thermal grease evenly on the CPU surface

Use PWM Y cable to connect two fans

Use RGB sync cable to connect 2 fans and the waterblock

Use RGB Controller power cable (SATA) to connect the RGB Control Box and PC power supply SATA connector

Breathing (Purple)

Breathing (Red)

Auto-run Flash

Auto-run Ripple

ENSURE THE FLAT MOUTH DIRECTION OF SCREW HEAD IS PARALLEL WITH THE ASSIGNED HOLE OF THE SOCKET

BACK PLATE MARKED INTEL SHOULD BACK TO THE MOTHERBOARD

INSERT THE INTEL LGA1700 SCREWS CLOSE FIT THE HOLES ON THE BACK PLATE

THEN USE THE WASHERS TO FIX THE INTEL LGA1700 SCREWS.

INSTALL THE BACK PLATE ON THE BACK OF THE MOTHERBOARD

FIX THE BACK PLATE WITH STAND OFF

REPLACE THE INTEL CLIP

APPLY THE THERMAL GREASE EVENLY ON THE CPU SURFACE

PLACE THE PUMP ON THE CPU.

AND TIGHTEN THE SPRING SCREWS UNTIL ALL FOUR CORNERS ARE SECURED.

Attach the fans to the radiator

Insert the position screws into the proper holes on the back plate. Then use the washers to fix the position screws

Place the stand-offs into the position screws to fix the back plate

Tighten the Intel LGA 2011/2011-3/2066 screw to the motherboards

Remove the protect film from the cold-plate

Use PWM Y cable to connect fans

Connect the RGB sync cable to the motherboard

Connect the RGB adapter to the RGB sync cable and the motherboard RGB header

If your motherboard do not support addressable RGB lighting function, you can use the RGB control box to sync the lighting of the cooler's water block

Connect the RGB sync cable to RGB control box

Introducing The Most Powerful Full Tower Case for Heavy Gamers

Supports Dual Liquid Coolers on Top and Bottom

ENERMAX POWER INNOVATION DESIGN

Attach the fans to the radiator

Install the back plate on to the back of the motherboard

Place position plate on stand-offs and use set screws to fix the plate

Remove the protection film from the cold-plate

Connect the pump power connector to the motherboard

Connect the connector to the motherboard

Connect the RGB sync cable 3-Pin connector to the motherboard

Connect the RGB Sync cable to the adapter and to the motherboard RGB header

Use RGB sync cable to connect the waterblock and fans

Use RGB Controller power cable (SATA) to connect the RGB Control Box and PC power supply SATA connector

Attach the fan to the radiator

Ensure the flat mouth direction of screw head is parallel with the assigned hole of the socket

Use the washers to fix the position screws

Install the back plate on the back of the motherboard

Fasten the Intel LGA 2011 screws to the motherboard

Apply the thermal grease on the CPU surface

Tighten the spring screws until all four corners are secured

Connect the PWM cable to the motherboard

Connect the RGB sync cable to the fan RGB connector

Connect the fan RGB connector to the motherboard

Shunt Channel Technology

Fan Design

Adjustable Fan Speed Control

Thermal Design Point (TDP)

Introduction

Fan Profile

Fan Specs

RGB Lighting

RGB Controller

Performance Test

Testing Setup

Benchmark Results

Noise Level

Conclusion